View AZ100EL16VO_1127349.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ARIZONA MICROTEK, INC.
AZ10EL16VO AZ100EL16VO
ECL/PECL Oscillator Gain Stage and Buffer with Enable FEATURES
* * * * * * * Green and RoHS Compliant Available 250ps Propagation Delay on Q Output High Voltage Gain vs. Standard EL16 For Oscillator Applications Available in 2x2 or 3x3mm MLP Package 75k Enable Pull-Down Resistor S-Parameter (.s2p) and IBIS Model Files Available on Arizona Microtek Website
DESCRIPTION
The AZ10/100EL16VO is an oscillator gain stage with a high gain output buffer including an enable. The QHG/QHG outputs have a voltage gain several times greater than the Q/Q outputs. An enable input (EN) allows continuous oscillator operation. When EN is LOW or floating (NC), input data is passed to both sets of outputs. When EN is HIGH, the QHG/QHG outputs will be forced LOW/HIGH respectively, while input data will continue to be passed to the Q/Q outputs. The EN input can be driven with an ECL/PECL signal or a CMOS logic signal. The input impedance of the D/D inputs remain constant for all operating modes since forcing the outputs via the EN pin does not power-down the chip but only disables the high gain QHG/QHG outputs. Input protection diodes are included on the D/D inputs for enhanced ESD protection. The EL16VO also provides a VBB output that supports 1.5mA sink/source current. When used, the VBB pin should be bypassed to ground or VCC via a 0.01F capacitor. Any used output must have an external pull down resistor. For 3.3V operation, an 180 resistor to VEE is recommended if an AC coupled load is present. At 5.0V, a 330 resistor is recommended for the AC load case. Alternately, a 50 load terminated to VCC - 2V or the Thevenin equivalent may be driven directly. Unused outputs may be left floating (NC). NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established. PIN/PAD DESCRIPTION
Q Q D
D
EN VBB
QHG QHG
PIN D/D Q/Q QHG/QHG VBB EN VCC VEE
FUNCTION Data Inputs Data Outputs Data Outputs w/High Gain Reference Voltage Output Enable Input Positive Supply Negative Supply
1630 S. STAPLEY DR., SUITE 127 * MESA, ARIZONA 85204 * USA * (480) 962-5881 * FAX (480) 890-2541 www.azmicrotek.com
AZ10EL16VO AZ100EL16VO
PACKAGE AVAILABILITY PACKAGE
MLP 8 (2x2) Green / RoHS Compliant / Lead (Pb) Free MLP 8 (2x2) MLP 8 (2x2) RoHS Compliant / Lead (Pb) Free MLP 8 (2x2x0.75) Green / RoHS Compliant / Lead (Pb) Free MLP 16 (3x3) MLP 16 (3x3) Green / RoHS Compliant / Lead (Pb) Free SOIC 8 SOIC 8 TSSOP 8 TSSOP 8 RoHS Compliant / Lead (Pb) Free TSSOP 8 TSSOP 8 RoHS Compliant / Lead (Pb) Free TSSOP 10 RoHS Compliant / Lead (Pb) Free TSSOP 10 RoHS Compliant / Lead (Pb) Free DIE DIE
1 2 3 4 5 6
PART NUMBER
AZ100EL16VONG AZ100EL16VONB AZ100EL16VONB+ AZ100EL16VONBG AZ10/100EL16VOL AZ10/100EL16VOLG AZ10EL16VOD AZ100EL16VOD AZ10EL16VOT AZ10EL16VOT+ AZ100EL16VOT AZ100EL16VOT+ AZ10EL16VOU+ AZ100EL16VOU+ AZ10/100EL16VOXP AZ10/100EL16VOXR
MARKING
P0G P4 P4+ P4G AZM 16J AZMG 16J AZM10 EL16VO AZM100 EL16VO AZT 16VO AZT+ 16VO AZH 16VO AZH+ 16VO AZT+ 16VOU AZH+ 16VOU N/A N/A
NOTES
1,2 1,2,3 1,2 1,2 1,2 1,2 1,2,4 1,2,4 1,2,4 1,2,4 1,2,4 1,2,4 1,2,4 1,2,4 5 6
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date code format: "Y" or "YY" for year followed by "WW" for week. Parts marked JNB for date codes prior to 4WW (prior to 2004). Date code "YWW" or "YYWW" on underside of part. Waffle Pack. Die thickness 180 m. Die on 7 inch Tape & Reel, 3k parts per reel. Die thickness 180 m.
June 2007 * REV - 23
www.azmicrotek.com 2
AZ10EL16VO AZ100EL16VO
TIMING DIAGRAM TRUTH TABLE EN Q/Q LOW or NC Data HIGH Data NC = No Connect QHG Data LOW QHG Data HIGH
D EN Q QHG
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Differential Input Voltage D/D Output Current -- Continuous IOUT -- Surge TA Operating Temperature Range TSTG Storage Temperature Range VI_DIFF is the voltage difference between D and D Symbol VCC VI VEE VI VI_DIFF Rating 0 to +6.0 0 to +6.0 -6.0 to 0 -6.0 to 0 0 to 1.6 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc Vpp1 mA C C
1.
June 2007 * REV - 23
www.azmicrotek.com 3
AZ10EL16VO AZ100EL16VO
10K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. Characteristic
1
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage D/D -1230 -430 EN -1230 VCC Input LOW Voltage -1500 D/D -2300 -1500 EN VEE Reference Voltage -1430 -1300 Input HIGH Current D/D 60 EN 150 Input LOW Current 0.5 Power Supply Current 40 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1080 -1950
-40C Typ
Max -890 -1650
Min -1020 -1950 -1170 -1170 -2260 VEE -1380
0C Typ
Max -840 -1630 -380 VCC -1480 -1480 -1260 60 150
Min -980 -1950 -1130 -1130 -2240 VEE -1360
25C Typ
Max -810 -1630 -360 VCC -1480 -1480 -1240 60 150
Min -910 -1950 -1060 -1060 -2190 VEE -1310
85C Typ
Max -720 -1595 -310 VCC -1445 -1445 -1190 60 150
Unit mV mV mV mV mV A A mA
0.5 40
0.5 40
0.5 40
10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. 3. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage 2870 2130 2920 2170 D/D1 2070 VCC 21301 VCC 21701 EN 20701 Input LOW Voltage 1800 1040 1820 1060 D/D1 1000 18001 VEE 18201 VEE EN VEE Reference Voltage1 1870 2000 1920 2040 1940 Input HIGH Current D/D 60 60 EN 150 150 Input LOW Current D/D 0.5 0.5 0.5 EN3 -300 -300 -300 Power Supply Current 40 40 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V. Specified with EN forced to VEE.
Min 2220 1350
-40C Typ
Max 2410 1650
Min 2280 1350
0C Typ
Max 2460 1670
Min 2320 1350
25C Typ
Max 2490 1670 2940 VCC 1820 18201 2060 60 150
Min 2390 1350 2240 22401 1110 VEE 1990
85C Typ
Max 2580 1705 2990 VCC 1855 18551 2110 60 150
Unit mV mV mV mV mV A A
0.5 -300 40 40
mA
June 2007 * REV - 23
www.azmicrotek.com 4
AZ10EL16VO AZ100EL16VO
10K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. 3. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage 4570 3830 4620 3870 D/D1 3770 VCC 38301 VCC 38701 EN 37701 Input LOW Voltage 3500 2740 3520 2760 D/D1 2700 35001 VEE 35201 VEE EN VEE Reference Voltage1 3570 3700 3620 3740 3640 Input HIGH Current D/D 60 60 EN 150 150 Input LOW Current 0.5 0.5 0.5 D/D -1400 -1400 EN3 -1400 Power Supply Current 40 40 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V. Specified with EN forced to VEE.
Min 3920 3050
-40C Typ
Max 4110 3350
Min 3980 3050
0C Typ
Max 4160 3370
Min 4020 3050
25C Typ
Max 4190 3370 4640 VCC 3520 35201 3760 60 150
Min 4090 3050 3940 39401 2810 VEE 3690
85C Typ
Max 4280 3405 4690 VCC 3555 35551 3810 60 150
Unit mV mV mV mV mV A A
0.5 -1400 40 40
mA
100K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. Characteristic
1
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage D/D -1165 -390 EN -1165 VCC Input LOW Voltage -1475 D/D -2250 -1475 EN VEE Reference Voltage -1390 -1250 Input HIGH Current D/D 60 EN 150 Input LOW Current 0.5 Power Supply Current 40 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1085 -1900
-40C Typ
Max -880 -1555
Min -1025 -1900 -1165 -1165 -2250 VEE -1390
0C Typ
Max -880 -1620 -390 VCC -1475 -1475 -1250 60 150
Min -1025 -1900 -1165 -1165 -2250 VEE -1390
25C Typ
Max -880 -1620 -390 VCC -1475 -1475 -1250 60 150
Min -1025 -1900 -1165 -1165 -2250 VEE -1390
85C Typ
Max -880 -1620 -390 VCC -1475 -1475 -1250 60 150
Unit mV mV mV mV mV A A mA
0.5 40
0.5 40
0.5 46
June 2007 * REV - 23
www.azmicrotek.com 5
AZ10EL16VO AZ100EL16VO
100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. 3. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage 2910 2135 2910 2135 D/D1 2135 VCC 21351 VCC 21351 EN 21351 Input LOW Voltage 1825 1050 1825 1050 D/D1 1050 18251 VEE 18251 VEE EN VEE Reference Voltage1 1910 2050 1910 2050 1910 Input HIGH Current D/D 60 60 EN 150 150 Input LOW Current 0.5 0.5 0.5 D/D -300 -300 -300 EN3 Power Supply Current 40 40 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V. Specified with EN forced to VEE.
Min 2215 1400
-40C Typ
Max 2420 1745
Min 2275 1400
0C Typ
Max 2420 1680
Min 2275 1400
25C Typ
Max 2420 1680 2910 VCC 1825 18251 2050 60 150
Min 2275 1400 2135 21351 1050 VEE 1910
85C Typ
Max 2420 1680 2910 VCC 1825 18251 2050 60 150
Unit mV mV mV mV mV A A
0.5 -300 40 46
mA
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. 3. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage 4610 3835 4610 3835 D/D1 3835 VCC 38351 VCC 38351 EN 38351 Input LOW Voltage 3525 2750 3525 2750 D/D1 2750 35251 VEE 35251 VEE EN VEE Reference Voltage1 3610 3750 3610 3750 3610 Input HIGH Current D/D 60 60 EN 150 150 Input LOW Current 0.5 0.5 0.5 D/D -1400 -1400 EN3 -1400 Power Supply Current 40 40 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V. Specified with EN forced to VEE.
Min 3915 3100
-40C Typ
Max 4120 3445
Min 3975 3100
0C Typ
Max 4120 3380
Min 3975 3100
25C Typ
Max 4120 3380 4610 VCC 3525 35251 3750 60 150
Min 3975 3100 3835 38351 2750 VEE 3610
85C Typ
Max 4120 3380 4610 VCC 3525 35251 3750 60 150
Unit mV mV mV mV mV A A
0.5 -1400 40 46
mA
June 2007 * REV - 23
www.azmicrotek.com 6
AZ10EL16VO AZ100EL16VO
AC Characteristics (VEE = -3.0V to -5.5V; VCC = GND or VEE = GND, VCC = +3.0V to +5.5V)
Symbol tPLH/tPHL Characteristic Min -40C Typ Max Min 0C Typ Max Min 25C Typ Max Min 85C Typ Max Unit ps ps mV ps Propagation Delay 100 300 100 300 100 200 300 100 300 D to Q/Q Outputs (SE) 150 450 150 450 150 290 450 150 450 D to QHG/QHG Outputs (SE) tSKEW Duty Cycle Skew1 (SE) 5 20 5 20 5 20 5 20 VPP (AC) Input Swing2 80 1000 80 1000 80 1000 80 1000 Output Rise/Fall Times tr/tf 80 240 80 240 80 135 240 80 240 (20% - 80%) 1. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. 2. VPP is the peak-to-peak differential input swing for which AC parameters are guaranteed. The device has a voltage gain of 20 to Q/Q outputs and a voltage gain of 100 to QHG/QHG outputs.
AC PP INPUT
D D V PP (AC)
Typical Large Signal Outputs, QHG/QHG
1000 900 800 VOUTpp (mV) 700 600 500 400 300 200 100 0 0 500 1000 1500 2000 2500 3000 3500 4000
FREQUENCY (MHz)
Measured with 750mv differential input, VEEP NC, QHG/QHG each terminated to VCC-2V via 50 resistors.
Q HG Q HG V OUTpp
June 2007 * REV - 23 www.azmicrotek.com 7
AZ10EL16VO AZ100EL16VO
2.05 0.00
2
-5.00
Magnitude
1.95
-10.00
Phase
S11 MAG S11 PH
1.9
-15.00
1.85
-20.00
1.8 50 150 250 350 450 550 650 750 850 950 1050 1150 1250 1350
-25.00
FREQUENCY (MHz)
S11, D to Q, 50 load to VCC - 2V
200
250
180
160
200
140
Magnitude
120
150
Phase
100
S12 MAG S12 PH
80
100
60
40
50
20
0 50 150 250 350 450 550 650 750 850 950 1050 1150 1250 1350
0
FREQUENCY (MHz)
S12, D to Q, 50 load to VCC - 2V
June 2007 * REV - 23
www.azmicrotek.com 8
AZ10EL16VO AZ100EL16VO
40 200.00
35
180.00
160.00 30 140.00 25
Magnitude
120.00
Phase
20
100.00
S21 MAG S21 PH
15
80.00
60.00 10 40.00 5
20.00
0 50 150 250 350 450 550 650 750 850 950 1050 1150 1250 1350
0.00
FREQUENCY (MHz)
S21, D to Q, 50 load to VCC - 2V
0.6
45.00
40.00 0.5 35.00
0.4
30.00
Magnitude
Phase
25.00 0.3 20.00
S22 MAG S22 PH
0.2
15.00
10.00 0.1 5.00
0 50 150 250 350 450 550 650 750 850 950 1050 1150 1250 1350
0.00
FREQUENCY (MHz)
S22, D to Q, 50 load to VCC - 2V
June 2007 * REV - 23
www.azmicrotek.com 9
AZ10EL16VO AZ100EL16VO
Application Circuit for CMOS Inputs
R11 Input Type AC Coupled (C2 in circuit) DC Coupled (C2 shorted)
3.3 V 430 750 CMOS 5 V CMOS 910 1.8K 1 R1 should be chosen so that the input swing on the D input with respect to D is in the range of 80 to 1000 mV, per the AC Characteristics table.
Recommended Component Values for CMOS Single Ended Inputs
June 2007 * REV - 23
www.azmicrotek.com 10
AZ10EL16VO AZ100EL16VO AZ10EL16VOU AZ100EL16VOU
10 VCC 9 QHG
Q1 D2 VBB / D 3 EN 4 8 VCC
AZ10EL16VOD AZ100EL16VOD AZ10EL16VOT AZ100EL16VOT
Q1 Q2 D3 D4 VBB 5
TSSOP 10
8 QHG 7 6 VEE EN
TSSOP 8 SOIC 8
7 QHG 6 QHG 5 VEE
AZ100EL16VON
AZ100EL16VONB
MLP 8, 2x2mm
Q D VBB / D EN 1 2 3 4 8 7 6 5 VCC QHG QHG VEE
MLP 8, 2x2mm
D VBB / D EN VEE 1 2 3 4 8 7 6 5 Q VCC QHG QHG
TOP VIEW
TOP VIEW
MLP 8: Bottom Center Pad may be left open or tied to VEE. Pin 4 is the VEE return.
AZ10/100EL16VOL
Q 16 NC 1 Q 15 NC 14 VCC 13
12
NC QHG QHG NC
MLP 16 (L) Package and DIE: 10K/100K Selection
Connect pin/pad 10K to VEE to select 10K operation. Float (NC) pin/pad 10K to select 100K operation. VEE connection must be less than 1. Pin 6 of the MLP 16 package may be connected to pin 7 (VEE) with no effect on the circuit.
D D VBB
2 3 4
5
MLP 16, 3x3 mm
11 10 9
6
7
8
EN
NC
VEE
10K
MPL 16: Bottom Center Pad may be left open or tied to VEE. Pin 7 is the VEE return. June 2007 * REV - 23 www.azmicrotek.com 11
AZ10EL16VO AZ100EL16VO
DIE PAD COORDINATES
AZ10/100EL16VO DIE:
EL16VO
A B C D
M
L
K J
DIE SIZE: 950u X 940u DIE THICKNESS: 180u BOND PAD: 85u X 85u
I H G
E
F
Note: Other die thicknesses available. Contact factory for further information. PAD CENTER COORDINATES NAME A B C D E F G H I J K L M
NC = No connect, leave open.
PAD DESIGNATION D D VBB EN VEE 10K QHG QHG NC VCC VCC Q Q
X(Microns) -342.5 -342.5 -342.5 -342.5 -33.5 126.5 312.5 312.5 312.5 312.5 302.5 142.5 -140.5
Y(Microns) 312.5 144.5 -87.0 -255.0 -312.5 -312.5 -248.5 -98.5 51.5 201.5 342.5 342.5 342.5
June 2007 * REV - 23
www.azmicrotek.com 12
AZ10EL16VO AZ100EL16VO
PACKAGE DIAGRAM MLP 8 2x2mm
Pin 1 Dot By Marking 2.0000.050
2.0000.050
MLP 8 (2x2mm)
TOP VIEW
0.3500.050 0.2500.050 8 7 0.500 bsc 6 5 1
Pin 1 Identification R0.100 TYP
2 1.2000.050 exp. pad 3 4 0.6000.050 exp. pad
BOTTOM VIEW
1.750 Ref.
0.7500.050 0.000-0.050
1
2
34 0.2030.025
SIDE VIEW
Note: All dimensions are in mm
June 2007 * REV - 23
www.azmicrotek.com 13
AZ10EL16VO AZ100EL16VO
PACKAGE DIAGRAM SOIC 8
MILLIMETERS DIM
MIN 0.10 1.25 0.25 0.36 0.19 4.8 3.8 1.27 5.80 1.05 0.40 0.60 0.25 0.25 0.10 0.30 0O
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
A A1 A2 A3 bp c D E e HE L Lp Q v w y Z
MAX 0.75 0.25 1.45 0.49 0.25 5.0 4.0 6.20 1.00 0.70
0.70 8O
INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O
June 2007 * REV - 23
www.azmicrotek.com 14
AZ10EL16VO AZ100EL16VO
PACKAGE DIAGRAM TSSOP 8
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z
MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O
June 2007 * REV - 23
www.azmicrotek.com 15
AZ10EL16VO AZ100EL16VO
PACKAGE DIAGRAM TSSOP 10
MILLIMETERS MIN MAX A A1 A2 A3 bp c D1 E2 e HE L Lp v w y Z 0.05 0.80 0.25 0.15 0.15 2.90 2.90 0.50 4.80 0.95 0.40 0.10 0.10 0.10 0.34 0O 0.67 6O 0.70 5.00 0.30 0.23 3.10 3.10 1.10 0.15 0.95
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
June 2007 * REV - 23
www.azmicrotek.com 16
AZ10EL16VO AZ100EL16VO PACKAGE DIAGRAM MLP 16 3x3mm
D
2. INDEX AREA (D/2 x E/2)
A D 2 E 2 E
3x e e
B
D2 D2/2
E2/2 E2
2 1
5.
2x 2x
aaa C aaa C TOP VIEW bbb M C A B
16 x b 3. 3x e BOTTOM VIEW
L
ccc C
A
4. 0.08 C SIDE VIEW
A3 C SEATING PLANE
A1
NOTES: 1. DIMENSIONING AND TOLERANCING CONFORM TO ASME T14-1994. 2. THE TERMINAL #1 AND PAD NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. 3. DIMENSION b APPLIES TO METALLIZED PAD AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM PAD TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PADS AS WELL AS THE TERMINALS. 5. INSIDE CORNERS OF METALLIZED PAD MAY BE SQUARE OR ROUNDED
MILLIMETERS DIM A A1 A3 b D D2 E E2 e L aaa bbb ccc MIN MAX 0.80 1.00 0.05 0.00 0.25 REF 0.18 0.30 3.10 2.90 1.95 0.25 3.10 2.90 1.95 0.25 0.50 BSC 0.50 0.30 0.25 0.10 0.10
June 2007 * REV - 23
www.azmicrotek.com 17
AZ10EL16VO AZ100EL16VO
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
June 2007 * REV - 23
www.azmicrotek.com 18

▲Up To Search▲

Price & Availability of AZ100EL16VO

	To Download AZ100EL16VO Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .